On 4 October 2015 at 23:17, Lee Jones <lee.jones@linaro.org> wrote:

Hooked up a serial cable and raised the loglevel.

For some reason the kernel isn't finding the SD card:

debug EMMC boot: print init OK
debug EMMC boot: send RST_N .
debug EMMC boot: start eMMC boot......
load fastboot1!
#PMU LDO15_REG_ADJ:0x00000054, STATUS3_LDO9_16:0x00000048
#PMU LDO22_REG:ADJ:0x00000057, STATUS4_LDO17_22:0x00000026
[BDID]boardid: 667 <6.6.7>
#select_hw_config, 58, board_id:0x0000002b
#select_hw_config, 71, array index:0
baudRate=115200, g_baudRate=115200
get_hw_config_int,hw_afreq:1200000.
get_efuse_value,efuse ATE_flag temp:0x02800000.
ATE PASS,ate flag value:0x00000001.
get_efuse_value,efuse acpu_freq change level:0x9a492400.
get_efuse_value,efuse afreq change level val:0x00000000.
get_efuse_value,efuse acpu_freq level:0x9a492400.
get_efuse_value,efuse acpu freq sys level:0x00000000.
###INFO###,soc_freq = hw_afreq, efuse_afreq:1200000,hw_afreq:1200000.
efuse ACPU 1.4G HPM:0.
efuse ACPU 1.2G HPM:0.
efuse ACPU 960M HPM:0.
fastboot: acpu_dvfs_init successful!
acpu_get_dvfs_volt,g_afreq_max_pro is :5��acpu max freq:1200000.
acpu support freq num:5
volt:0x0000003a 0x0000003a 0x0000004a 0x0000005b 0x0000006b
acpu start prof:0x00000004
acpu magic:0x5a5ac5c5
#### success !!!!! set_acpu_freq: acpu support freq num is 5 and start is 4 .
get_ddr_type 1; (lpddr2: 0; lpddr3: 1)
ddr_init(): get_ddr_type: 1
ddr freq: 800000
in lpddr3_init: mode: 0; freq_config: 800
lpddr3_150_rank0_init_pass
lpddr3_150_rank1_init_pass
lpddr3_266_rank0_init_pass
lpddr3_266_rank1_init_pass
lpddr3_400_rank0_init_pass
lpddr3_400_rank1_init_pass
lpddr3_rank0_phydraminit_pass
lpddr3_cat_pass
lpddr3_533_rank0_init_pass
rdet_lbs_passrdet_ds_passrdet_rbs_av_passwdet_lbs_passwdet_ds_passwdet_rbs_av_passlpddr3_533_rank1_init_pass
lpddr3_rank0_phydraminit_pass
lpddr3_cat_pass
lpddr3_800_rank0_init_pass
rdet_lbs_passrdet_ds_passrdet_rbs_av_passwdet_lbs_passwdet_ds_passwdet_rbs_av_passlpddr3_800_rank1_init_pass
tmp_freq: 400000
MR8 value=:0x0000001b
MR5 value=:0x00000003
Elpida DDR
MR6 value=:0x00000002
MR5 value=:0x00000000
[MR7,MR6,MR5]=:0x00000203
ddr init pll1 0x00007800!ddrc_qos_init done

[emmc_set_card_ready]emmc id:0x5bcf61c7 0x4742aaf6 0x4d433034 0xfe014e4d

[emmc_set_card_ready]manufid: 0x000000fe
DDR mode emmc
--error: gps/ldo16
load fastboot2 succ and run it now!
[1970:1:1 0:31:46][34890]GET DDR capacity. g_ddr_last_addr=0x3fffffff !!
[1970:1:1 0:31:46][37239]
[emmc_set_card_ready]emmc id:0x5bcf61c7 0x4742aaf6 0x4d433034 0xfe014e4d
[1970:1:1 0:31:46][37525]
[emmc_set_card_ready]manufid: 0x000000fe
[1970:1:1 0:31:46][37789]DDR mode emmc
[1970:1:1 0:31:46][40029][init_nve]NV init ok!

[1970:1:1 0:31:46][40134][BDID]boardid: 43.
[1970:1:1 0:31:46][40264][BDID]CHIP_ID:0x48696220.
[1970:1:1 0:31:46][40415][BDID]pmu_id:0x00000011.
[1970:1:1 0:31:46][40563]#select_hw_config, 58, board_id:0x0000002b
[1970:1:1 0:31:46][40762]#select_hw_config, 71, array index:0
[1970:1:1 0:31:46][40946]can't find ptn boot
[1970:1:1 0:31:46][41078]
!!!!!!secure_verify_dt FAIL!!!!!!
[1970:1:1 0:31:46][41298]boot!! BOOT_MAGIC ERROR
[1970:1:1 0:31:46][41407]can't find ptn recovery
[1970:1:1 0:31:46][41550]
!!!!!!dtb_init FAIL!!!!!!
[1970:1:1 0:31:46][41710]baudRate=115200, g_baudRate=115200
[1970:1:1 0:31:46][41886]USB FastBoot: V2.0
[1970:1:1 0:31:46][42020]Machine ID: 2967 v0
[1970:1:1 0:31:46][42162]ydb Build Date: May 14 2015, 23:55:05

[1970:1:1 0:31:46][42364]Serial Number: serialv1.0

[1970:1:1 0:31:46][42523]END ADDRESS=07038950
[1970:1:1 0:31:46][42660]#ddr [0xf7032580]:0x00000202
[1970:1:1 0:31:46][42819]#ddr [0xf7032594]:0x00001003
[1970:1:1 0:31:46][42979]#ddr [0xf7128040]:0x00002001
[1970:1:1 0:31:46][43140]--error: cdma_gsm/boardid_virtual
[1970:1:1 0:31:46][43310][virtual config do not exist]
[1970:1:1 0:31:46][43701]--error: cdma_gsm/cg_mode
[1970:1:1 0:31:46][43806][mode config do not exist]
[1970:1:1 0:31:46][43961]--error: CCPU_GPIO_INT_GROUP/group_num
[1970:1:1 0:31:46][44149][BDID]boardid: 43.
[1970:1:1 0:31:46][44281]
[1970:1:1 0:31:46][44360]get_reserve_mem_info:can not open g_fdt
[1970:1:1 0:31:46][44553]First Cold Start
[1970:1:1 0:31:46][44678]First Cold Start
[1970:1:1 0:31:46][44804]Set Warm Start Flag End
[1970:1:1 0:31:46][44949][fastboot]: dump_mode check_wdt_reset: 0
[1970:1:1 0:31:46][45143][fastboot]: no key pressed
[1970:1:1 0:31:46][45299]can't find ptn misc
[1970:1:1 0:31:46][45431]can't find ptn misc
[1970:1:1 0:31:46][45563][fastboot]: reboot type 0x00000000
[1970:1:1 0:31:46][45740][fastboot]: get_poweroff_alarm 0x00000000.
[1970:1:1 0:31:46][49190]get oeminfo 97, len 16
[1970:1:1 0:31:46][49290]can't find oeminfo.
[1970:1:1 0:31:46][49422]cannot get oeminfo lock state info
[1970:1:1 0:31:46][49598]get oeminfo 35, len 12
[1970:1:1 0:31:46][49742]can't find oeminfo.
[1970:1:1 0:31:46][49874]cannot get oeminfo root type info
[1970:1:1 0:31:46][50048]backdoor.lock_state.fb_lock_stat = 1
[1970:1:1 0:31:46][50230]backdoor.lock_state.user_lock_stat = 0
[1970:1:1 0:31:46][50418]backdoor.lock_state.check_root_stat = 0
[1970:1:1 0:31:46][50608]backdoor.lock_state.check_sign_stat = 0
[1970:1:1 0:31:46][50799]widevine state already is locked
[1970:1:1 0:31:46][50970]pwc_switch_nv_read: force enabling cpu
frequency change for ACPU
[1970:1:1 0:31:46][51232]pwc_switch_nv_read: Reg[f7030d04]=0x02000020
[1970:1:1 0:31:46][51441]
case NORMAL_MODE:
[1970:1:1 0:31:46][51783]can't find ptn misc
[1970:1:1 0:31:46][51873]
execute_load_kernel: can't read power_state from misc
[1970:1:1 0:31:46][52115]SD Card has been detected.
[1970:1:1 0:31:46][52269][fastboot]: sd_init begin
[1970:1:1 0:31:46][57208][fastboot]: sd_init over
[1970:1:1 0:31:46][57400]fat ok
[1970:1:1 0:31:46][57496]Partition 1: Filesystem: FAT16 "boot "
[1970:1:1 0:31:54][315288]rest_init: read kernel bytes 00b68148
[1970:1:1 0:31:56][383416]rest_init: read ramdisk bytes 002fb17f
[1970:1:1 0:31:56][385001]rest_init: read dtb bytes 0000ac2a
[1970:1:1 0:31:56][385460]rest_init: read cmdline console=tty0
console=ttyAMA0,115200n8 root=/dev/mmcblk1p2 rootwait rw loglevel=7

[1970:1:1 0:31:56][385807]cmd_line_mem_size = 0x40000000
[1970:1:1 0:31:56][385974]creat_kernelsize_cmdline : cmd_line_mem_size
= 0x0000038cMB
[1970:1:1 0:31:56][386230]get_efuse_thermal_value : 0x9a492400.
[1970:1:1 0:31:56][386469]--error: lcd/devices
[1970:1:1 0:31:56][386569]--error: lcd/devices
[1970:1:1 0:31:56][386720]cmdline of bitmap abnormal reset is
bitmapofabnrst=0x00000008
[1970:1:1 0:31:56][386970]cmdline:pmu_nv_info_addr=0x00000000[1970:1:1
0:31:56][387134]cmdline of boot_slice is boot_slice=0x0005e83c
[1970:1:1 0:31:56][387366]uart0 nve config is enabled, uart console
will be set by UART0 nv_data[1] !
[1970:1:1 0:31:56][387643]create_console_cmdline UART0 nv_data[1] is
49, uart console will be Enabled.
[1970:1:1 0:31:56][387950]console cmdline:console=ttyAMA0,115200
[1970:1:1 0:31:56][388146]get_cmdlind_from_nve nv is INVALID
[1970:1:1 0:31:56][388317]creat_flash_nv_cmdline error
[1970:1:1 0:31:56][388485]cmdline size = 505
[1970:1:1 0:31:57][390532]Could not find hisi_ion_no_iommu@0 node.
[1970:1:1 0:31:57][390685]Could not find memreserve_base node : 0x00000000.
[1970:1:1 0:31:57][391400]hifi nv old status:0x05a0005c is 0x2aaeaaaa
[1970:1:1 0:31:57][391562]
64 start hifi ok
[ 0.000000] Initializing cgroup subsys cpu
[ 0.000000] Initializing cgroup subsys cpuacct
[ 0.000000] Linux version 3.18.0-linaro-hikey
(buildslave@x86-64-07) (gcc version 4.9.2 20140904 (prerelease)
(crosstool-NG linaro-1.13.1-4.9-2014.09 - Linaro GCC 4.9-2014.09) ) #1
SMP PREEMPT We5
[ 0.000000] CPU: AArch64 Processor [410fd033] revision 3
[ 0.000000] Detected VIPT I-cache on CPU0
[ 0.000000] Ignoring memory range 0x0 - 0x7400000
[ 0.000000] Memory limited to 908MB
[ 0.000000] efi: Getting EFI parameters from FDT:
[ 0.000000] efi: UEFI not found.
[ 0.000000] cma: Reserved 16 MiB at 0x000000003f000000
[ 0.000000] PERCPU: Embedded 14 pages/cpu @ffffffc037b42000 s18432
r8192 d30720 u57344
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on.
Total pages: 229270
[ 0.000000] Kernel command line: iommu_ddr_size=0x40000000
console=tty0 console=ttyAMA0,115200n8 root=/dev/mmcblk1p2 rootwait rw
loglevel=7
[ 0.000000] mem=908M boardid=0x48696220,0x00000011,0x0000002b
thermal_trim=0x9a492400 pd_charge=0 boottype=defaultnormal
enter_recovery=0 androidboot.swtype=normal fastboot_version=
himntn=111
[ 0.000000] log_buf_len individual max cpu contribution: 4096 bytes
[ 0.000000] log_buf_len total cpu_extra contributions: 28672 bytes
[ 0.000000] log_buf_len min size: 16384 bytes
[ 0.000000] log_buf_len: 65536 bytes
[ 0.000000] early log buf free: 14436(88%)
[ 0.000000] PID hash table entries: 4096 (order: 3, 32768 bytes)
[ 0.000000] Dentry cache hash table entries: 131072 (order: 8, 1048576 bytes)
[ 0.000000] Inode-cache hash table entries: 65536 (order: 7, 524288 bytes)
[ 0.000000] Memory: 881168K/929792K available (7621K kernel code,
628K rwdata, 3068K rodata, 356K init, 495K bss, 48624K reserved)
[ 0.000000] Virtual kernel memory layout:
[ 0.000000] vmalloc : 0xffffff8000000000 - 0xffffffbdffff0000
( 247 GB)
[ 0.000000] vmemmap : 0xffffffbe00000000 - 0xffffffbfc0000000
( 7 GB maximum)
[ 0.000000] 0xffffffbe00196000 - 0xffffffbe00e00000
( 12 MB actual)
[ 0.000000] PCI I/O : 0xffffffbffa000000 - 0xffffffbffb000000
( 16 MB)
[ 0.000000] fixed : 0xffffffbffbdfe000 - 0xffffffbffbdff000
( 4 KB)
[ 0.000000] modules : 0xffffffbffc000000 - 0xffffffc000000000
( 64 MB)
[ 0.000000] memory : 0xffffffc000000000 - 0xffffffc038c00000
( 908 MB)
[ 0.000000] .init : 0xffffffc000af2000 - 0xffffffc000b4b000
( 356 KB)
[ 0.000000] .text : 0xffffffc000080000 - 0xffffffc000af1434
( 10694 KB)
[ 0.000000] .data : 0xffffffc000b4b000 - 0xffffffc000be8148
( 629 KB)
[ 0.000000] Preemptible hierarchical RCU implementation.
[ 0.000000] RCU restricting CPUs from NR_CPUS=64 to nr_cpu_ids=8.
[ 0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=8
[ 0.000000] NR_IRQS:64 nr_irqs:64 16
[ 0.000000] Architected cp15 timer(s) running at 1.20MHz (virt).
[ 0.000005] sched_clock: 56 bits at 1200kHz, resolution 833ns,
wraps every 3579139414016ns
[ 0.000368] Console: colour dummy device 80x25
[ 0.000774] console [tty0] enabled
[ 0.001574] allocated 4194304 bytes of page_cgroup
[ 0.001585] please try 'cgroup_disable=memory' option if you don't
want memory cgroups
[ 0.001608] Calibrating delay loop (skipped), value calculated
using timer frequency.. 2.40 BogoMIPS (lpj=12000)
[ 0.001628] pid_max: default: 32768 minimum: 301
[ 0.001737] Security Framework initialized
[ 0.001758] SELinux: Initializing.
[ 0.001835] Mount-cache hash table entries: 2048 (order: 2, 16384 bytes)
[ 0.001850] Mountpoint-cache hash table entries: 2048 (order: 2, 16384 bytes)
[ 0.002348] Initializing cgroup subsys memory
[ 0.002378] Initializing cgroup subsys freezer
[ 0.002393] Initializing cgroup subsys hugetlb
[ 0.002408] Initializing cgroup subsys debug
[ 0.003274] /cpus/cpu@0: Missing clock-frequency property
[ 0.003302] /cpus/cpu@1: Missing clock-frequency property
[ 0.003329] /cpus/cpu@2: Missing clock-frequency property
[ 0.003356] /cpus/cpu@3: Missing clock-frequency property
[ 0.003385] /cpus/cpu@4: Missing clock-frequency property
[ 0.003414] /cpus/cpu@5: Missing clock-frequency property
[ 0.003446] /cpus/cpu@6: Missing clock-frequency property
[ 0.003478] /cpus/cpu@7: Missing clock-frequency property
[ 0.003564] hw perfevents: enabled with arm/armv8-pmuv3 PMU driver,
7 counters available
[ 0.003632] EFI services will not be available.
[ 0.080298] CPU1: Booted secondary processor
[ 0.080305] Detected VIPT I-cache on CPU1
[ 0.100255] CPU2: Booted secondary processor
[ 0.100260] Detected VIPT I-cache on CPU2
[ 0.120278] CPU3: Booted secondary processor
[ 0.120284] Detected VIPT I-cache on CPU3
[ 0.140301] CPU4: Booted secondary processor
[ 0.140309] Detected VIPT I-cache on CPU4
[ 0.160320] CPU5: Booted secondary processor
[ 0.160325] Detected VIPT I-cache on CPU5
[ 0.180335] CPU6: Booted secondary processor
[ 0.180341] Detected VIPT I-cache on CPU6
[ 0.200349] CPU7: Booted secondary processor
[ 0.200354] Detected VIPT I-cache on CPU7
[ 0.200445] Brought up 8 CPUs
[ 0.200623] SMP: Total of 8 processors activated.
[ 0.201447] devtmpfs: initialized
[ 0.209346] xor: measuring software checksum speed
[ 0.300074] 8regs : 1456.800 MB/sec
[ 0.400134] 8regs_prefetch: 1331.200 MB/sec
[ 0.500191] 32regs : 1614.000 MB/sec
[ 0.600252] 32regs_prefetch: 1419.600 MB/sec
[ 0.600270] xor: using function: 32regs (1614.000 MB/sec)
[ 0.600350] pinctrl core: initialized pinctrl subsystem
[ 0.600892] regulator-dummy: no parameters
[ 0.613530] NET: Registered protocol family 16
[ 0.616659] vdso: 2 pages (1 code @ ffffffc000b51000, 1 data @
ffffffc000b50000)
[ 0.616816] hw-breakpoint: found 6 breakpoint and 4 watchpoint registers.
[ 0.617766] software IO TLB [mem 0x3c800000-0x3cc00000] (4MB)
mapped at [ffffffc035400000-ffffffc0357fffff]
[ 0.618974] DMA: preallocated 256 KiB pool for atomic allocations
[ 0.619159] Serial: AMBA PL011 UART driver
[ 0.620233] uart-pl011 f8015000.uart: ttyAMA0 at MMIO 0xf8015000
(irq = 68, base_baud = 0) is a PL011 rev2
[ 1.198964] console [ttyAMA0] enabled
[ 1.203307] uart-pl011 f7111000.uart: could not find pctldev for
node /smb/pinmux@f7010000/uart1_pmx_func, deferring probe
[ 1.214409] amba f7111000.uart: Driver uart-pl011 requests probe deferral
[ 1.221500] uart-pl011 f7112000.uart: could not find pctldev for
node /smb/pinmux@f7010000/uart2_pmx_func, deferring probe
[ 1.232589] amba f7112000.uart: Driver uart-pl011 requests probe deferral
[ 1.239677] uart-pl011 f7113000.uart: could not find pctldev for
node /smb/pinmux@f7010000/uart3_pmx_func, deferring probe
[ 1.250764] amba f7113000.uart: Driver uart-pl011 requests probe deferral
[ 1.257846] uart-pl011 f7114000.uart: could not find pctldev for
node /smb/pinmux@f7010000/uart4_pmx_func, deferring probe
[ 1.268933] amba f7114000.uart: Driver uart-pl011 requests probe deferral
[ 1.509352] raid6: int64x1 292 MB/s
[ 1.679278] raid6: int64x2 426 MB/s
[ 1.849471] raid6: int64x4 619 MB/s
[ 2.019476] raid6: int64x8 634 MB/s
[ 2.189608] raid6: neonx1 463 MB/s
[ 2.359699] raid6: neonx2 716 MB/s
[ 2.529825] raid6: neonx4 943 MB/s
[ 2.699879] raid6: neonx8 943 MB/s
[ 2.703639] raid6: using algorithm neonx4 (943 MB/s)
[ 2.708614] raid6: using intx1 recovery algorithm
[ 2.713815] platform regulator@0: Driver reg-fixed-voltage requests
probe deferral
[ 2.721490] platform fixedregulator@1: Driver reg-fixed-voltage
requests probe deferral
[ 2.729844] vgaarb: loaded
[ 2.733035] SCSI subsystem initialized
[ 2.737549] usbcore: registered new interface driver usbfs
[ 2.743136] usbcore: registered new interface driver hub
[ 2.748585] usbcore: registered new device driver usb
[ 2.754004] i2c_designware f7102000.i2c: could not find pctldev for
node /smb/pinmux@f7010000/i2c2_pmx_func, deferring probe
[ 2.765267] platform f7102000.i2c: Driver i2c_designware requests
probe deferral
[ 2.772840] Linux video capture interface: v2.00
[ 2.778027] Advanced Linux Sound Architecture Driver Initialized.
[ 2.785063] NetLabel: Initializing
[ 2.788485] NetLabel: domain hash size = 128
[ 2.792851] NetLabel: protocols = UNLABELED CIPSOv4
[ 2.797877] NetLabel: unlabeled traffic allowed by default
[ 2.804192] Switched to clocksource arch_sys_counter
[ 2.847353] G3D_PD_VDD: no parameters
[ 2.851193] SOC_MED: no parameters
[ 2.864870] NET: Registered protocol family 2
[ 2.870006] TCP established hash table entries: 8192 (order: 4, 65536 bytes)
[ 2.877211] TCP bind hash table entries: 8192 (order: 5, 131072 bytes)
[ 2.883954] TCP: Hash tables configured (established 8192 bind 8192)
[ 2.890413] TCP: reno registered
[ 2.893658] UDP hash table entries: 512 (order: 2, 16384 bytes)
[ 2.899640] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes)
[ 2.906348] NET: Registered protocol family 1
[ 2.911154] RPC: Registered named UNIX socket transport module.
[ 2.917104] RPC: Registered udp transport module.
[ 2.921819] RPC: Registered tcp transport module.
[ 2.926544] RPC: Registered tcp NFSv4.1 backchannel transport module.
[ 2.933339] Trying to unpack rootfs image as initramfs...
[ 3.133848] Freeing initrd memory: 3056K (ffffffc007c00000 -
ffffffc007efc000)
[ 3.142232] kvm [1]: HYP mode not available
[ 3.150392] futex hash table entries: 2048 (order: 5, 131072 bytes)
[ 3.156969] audit: initializing netlink subsys (disabled)
[ 3.162443] audit: type=2000 audit(2.919:1): initialized
[ 3.168943] HugeTLB registered 2 MB page size, pre-allocated 0 pages
[ 3.176335] VFS: Disk quotas dquot_6.5.2
[ 3.180348] Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
[ 3.188072] NFS: Registering the id_resolver key type
[ 3.193176] Key type id_resolver registered
[ 3.197386] Key type id_legacy registered
[ 3.201755] fuse init (API version 7.23)
[ 3.206117] 9p: Installing v9fs 9p2000 file system support
[ 3.211693] msgmni has been set to 1759
[ 3.218650] io scheduler noop registered
[ 3.222636] io scheduler cfq registered (default)
[ 3.228872] pinctrl-single f7010000.pinmux: 159 pins at pa
ffffff800009a000 size 636
[ 3.237282] pinctrl-single f7010800.pinmux: 163 pins at pa
ffffff800009c800 size 652
[ 3.245334] pinctrl-single f8001800.pinmux: 30 pins at pa
ffffff800009e800 size 120
[ 3.253660] pl061_gpio f8011000.gpio: PL061 GPIO chip
@0x00000000f8011000 registered
[ 3.261662] pl061_gpio f8012000.gpio: PL061 GPIO chip
@0x00000000f8012000 registered
[ 3.269655] pl061_gpio f8013000.gpio: PL061 GPIO chip
@0x00000000f8013000 registered
[ 3.277647] pl061_gpio f8014000.gpio: PL061 GPIO chip
@0x00000000f8014000 registered
[ 3.285651] pl061_gpio f7020000.gpio: PL061 GPIO chip
@0x00000000f7020000 registered
[ 3.293624] pl061_gpio f7021000.gpio: PL061 GPIO chip
@0x00000000f7021000 registered
[ 3.301615] pl061_gpio f7022000.gpio: PL061 GPIO chip
@0x00000000f7022000 registered
[ 3.309609] pl061_gpio f7023000.gpio: PL061 GPIO chip
@0x00000000f7023000 registered
[ 3.317595] pl061_gpio f7024000.gpio: PL061 GPIO chip
@0x00000000f7024000 registered
[ 3.325585] pl061_gpio f7025000.gpio: PL061 GPIO chip
@0x00000000f7025000 registered
[ 3.333557] pl061_gpio f7026000.gpio: PL061 GPIO chip
@0x00000000f7026000 registered
[ 3.341556] pl061_gpio f7027000.gpio: PL061 GPIO chip
@0x00000000f7027000 registered
[ 3.349551] pl061_gpio f7028000.gpio: PL061 GPIO chip
@0x00000000f7028000 registered
[ 3.357551] pl061_gpio f7029000.gpio: PL061 GPIO chip
@0x00000000f7029000 registered
[ 3.365541] pl061_gpio f702a000.gpio: PL061 GPIO chip
@0x00000000f702a000 registered
[ 3.373544] pl061_gpio f702b000.gpio: PL061 GPIO chip
@0x00000000f702b000 registered
[ 3.381531] pl061_gpio f702c000.gpio: PL061 GPIO chip
@0x00000000f702c000 registered
[ 3.389537] pl061_gpio f702d000.gpio: PL061 GPIO chip
@0x00000000f702d000 registered
[ 3.397525] pl061_gpio f702e000.gpio: PL061 GPIO chip
@0x00000000f702e000 registered
[ 3.405525] pl061_gpio f702f000.gpio: PL061 GPIO chip
@0x00000000f702f000 registered
[ 3.416492] k3-dma f7370000.dma: initialized
[ 3.424994] Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled
[ 3.433162] [drm] Initialized drm 1.1.0 20060810
[ 3.438903] [drm] Initialized hisi 1.0.0 20141224 on minor 0
[ 3.445210] [drm] failed to find slave encoder i2c client
[ 3.450648] platform f4107800.dsi: Driver hisi-dsi requests probe deferral
[ 3.464252] brd: module loaded
[ 3.470545] loop: module loaded
[ 3.475687] ldo2: Operation of current configuration missing
[ 3.481373] ldo2: 2500 <--> 3200 mV at 2500 mV 2500 <--> 3200 mA normal
[ 3.488457] ldo7: Operation of current configuration missing
[ 3.494137] ldo7: 1800 <--> 3300 mV at 2850 mV 1800 <--> 3300 mA
normal standby
[ 3.501827] ldo10: Operation of current configuration missing
[ 3.507609] ldo10: 1800 <--> 3000 mV at 2850 mV 1800 <--> 3000 mA
normal standby
[ 3.515389] ldo13: Operation of current configuration missing
[ 3.521155] ldo13: 1600 <--> 1950 mV at 1800 mV 1600 <--> 1950 mA
normal standby
[ 3.528929] ldo14: Operation of current configuration missing
[ 3.534711] ldo14: 2500 <--> 3200 mV at 2800 mV 2500 <--> 3200 mA normal
[ 3.541865] ldo15: Operation of current configuration missing
[ 3.547768] ldo15: 1600 <--> 1950 mV at 1800 mV 1600 <--> 1950 mA
normal standby
[ 3.555540] ldo17: Operation of current configuration missing
[ 3.561308] ldo17: 2500 <--> 3200 mV at 3000 mV 2500 <--> 3200 mA normal
[ 3.568473] ldo19: Operation of current configuration missing
[ 3.574255] ldo19: 1800 <--> 3000 mV at 3000 mV 1800 <--> 3000 mA
normal standby
[ 3.581899] hi655x_regulator f8000000.pmic:regulator@a40:
fake_of_get_regulator_init_data no consumer_supplies
[ 3.592129] ldo21: Operation of current configuration missing
[ 3.598031] ldo21: 1650 <--> 2000 mV at 1800 mV 1650 <--> 2000 mA normal
[ 3.605217] ldo22: Operation of current configuration missing
[ 3.611105] ldo22: 900 <--> 1200 mV at 1200 mV 900 <--> 1200 mA normal
[ 3.619045] tun: Universal TUN/TAP device driver, 1.6
[ 3.624108] tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
[ 3.631117] PPP generic driver version 2.4.2
[ 3.635605] PPP BSD Compression module registered
[ 3.640350] PPP Deflate Compression module registered
[ 3.645480] PPP MPPE Compression module registered
[ 3.650313] NET: Registered protocol family 24
[ 3.654875] pegasus: v0.9.3 (2013/04/25), Pegasus/Pegasus II USB
Ethernet driver
[ 3.662385] usbcore: registered new interface driver pegasus
[ 3.668158] usbcore: registered new interface driver rtl8150
[ 3.673915] usbcore: registered new interface driver r8152
[ 3.679527] usbcore: registered new interface driver asix
[ 3.685036] usbcore: registered new interface driver ax88179_178a
[ 3.691234] usbcore: registered new interface driver cdc_ether
[ 3.697180] usbcore: registered new interface driver dm9601
[ 3.702864] usbcore: registered new interface driver CoreChips
[ 3.708829] usbcore: registered new interface driver smsc75xx
[ 3.714712] usbcore: registered new interface driver smsc95xx
[ 3.720556] usbcore: registered new interface driver net1080
[ 3.726327] usbcore: registered new interface driver plusb
[ 3.731910] usbcore: registered new interface driver cdc_subset
[ 3.737945] usbcore: registered new interface driver zaurus
[ 3.743622] usbcore: registered new interface driver MOSCHIP
usb-ethernet driver
[ 3.751208] usbcore: registered new interface driver cdc_ncm
[ 3.757687] f72c0000.usb supply vusb_d not found, using dummy regulator
[ 3.764398] f72c0000.usb supply vusb_a not found, using dummy regulator
[ 3.804247] dwc2 f72c0000.usb: EPs: 16, dedicated fifos, 1920
entries in SPRAM
[ 4.654857] dwc2 f72c0000.usb: DWC OTG Controller
[ 4.659603] dwc2 f72c0000.usb: new USB bus registered, assigned bus number 1
[ 4.666837] dwc2 f72c0000.usb: irq 109, io mem 0x00000000
[ 4.673135] hub 1-0:1.0: USB hub found
[ 4.676943] hub 1-0:1.0: 1 port detected
[ 4.681306] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 4.687890] ehci-pci: EHCI PCI platform driver
[ 4.692463] ehci-platform: EHCI generic platform driver
[ 4.697983] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 4.704259] ohci-pci: OHCI PCI platform driver
[ 4.708799] ohci-platform: OHCI generic platform driver
[ 4.714648] usbcore: registered new interface driver cdc_acm
[ 4.720321] cdc_acm: USB Abstract Control Model driver for USB
modems and ISDN adapters
[ 4.728482] usbcore: registered new interface driver usb-storage
[ 4.735115] mousedev: PS/2 mouse device common for all mice
[ 4.741974] rtc-pl031 f8003000.rtc: rtc core: registered pl031 as rtc0
[ 4.748820] i2c /dev entries driver
[ 4.773570] hisi_thermal f7030700.tsensor: THERMAL ALARM: T > 50
[ 4.779848] device-mapper: ioctl: 4.28.0-ioctl (2014-09-17)
initialised: dm-devel@redhat.com
[ 4.789835] sdhci: Secure Digital Host Controller Interface driver
[ 4.796064] sdhci: Copyright(c) Pierre Ossman
[ 4.800487] Synopsys Designware Multimedia Card Interface Driver
[ 4.807031] dwmmc_k3 f723d000.dwmmc0: fifo-depth property not
found, using value of FIFOTH register as default
[ 4.817222] dwmmc_k3 f723d000.dwmmc0: Using internal DMA controller.
[ 4.823590] dwmmc_k3 f723d000.dwmmc0: Version ID is 250a
[ 4.828938] dwmmc_k3 f723d000.dwmmc0: DW MMC controller at irq 104,
32 bit host data width, 8 deep fifo
[ 4.838466] dwmmc_k3 f723d000.dwmmc0: No vqmmc regulator found
[ 4.864388] mmc_host mmc0: Bus speed (slot 0) = 25000000Hz (slot
req 400000Hz, actual 390625HZ div = 32)
[ 4.884467] dwmmc_k3 f723d000.dwmmc0: 1 slots initialized
[ 4.891074] dwmmc_k3 f723e000.dwmmc1: fifo-depth property not
found, using value of FIFOTH register as default
[ 4.901280] dwmmc_k3 f723e000.dwmmc1: Using internal DMA controller.
[ 4.907656] dwmmc_k3 f723e000.dwmmc1: Version ID is 250a
[ 4.912994] dwmmc_k3 f723e000.dwmmc1: DW MMC controller at irq 105,
32 bit host data width, 128 deep fifo
[ 4.922757] dwmmc_k3 f723e000.dwmmc1: Got CD GPIO
[ 4.928323] mmc0: BKOPS_EN bit is not set
[ 4.934161] mmc_host mmc0: Bus speed (slot 0) = 50000000Hz (slot
req 52000000Hz, actual 50000000HZ div = 0)
[ 4.944459] mmc_host mmc1: Bus speed (slot 0) = 25000000Hz (slot
req 400000Hz, actual 390625HZ div = 32)
[ 4.945868] mmc0: new high speed MMC card at address 0001
[ 4.946145] mmcblk0: mmc0:0001 MMC04G 3.65 GiB
[ 4.946226] mmcblk0boot0: mmc0:0001 MMC04G partition 1 1.00 MiB
[ 4.946361] mmcblk0boot1: mmc0:0001 MMC04G partition 2 1.00 MiB
[ 4.956487] GPT:last_usable_lbas don't match.
[ 4.956490] GPT:7471103 != 7471070
[ 4.956493] GPT:disk_guids don't match.
[ 4.956496] GPT:partition_entry_array_crc32 values don't match:
0x74cd9524 != 0xf9afe40e
[ 4.956499] GPT:Primary header thinks Alt. header is not at the end
of the disk.
[ 4.956500] GPT:7471103 != 7667711
[ 4.956502] GPT:Alternate GPT header not at the end of the disk.
[ 4.956504] GPT:7471103 != 7667711
[ 4.956506] GPT: Use GNU Parted to correct GPT errors.
[ 4.956535] mmcblk0: p1 p2 p3 p4 p5 p6 p7 p8 p9
[ 5.045320] dwmmc_k3 f723e000.dwmmc1: 1 slots initialized
[ 5.052167] dwmmc_k3 f723f000.dwmmc2: fifo-depth property not
found, using value of FIFOTH register as default
[ 5.062416] dwmmc_k3 f723f000.dwmmc2: Using internal DMA controller.
[ 5.064231] usb 1-1: new full-speed USB device number 2 using dwc2
[ 5.074984] dwmmc_k3 f723f000.dwmmc2: Version ID is 250a
[ 5.080320] dwmmc_k3 f723f000.dwmmc2: DW MMC controller at irq 106,
32 bit host data width, 128 deep fifo
[ 5.090063] platform f723f000.dwmmc2: Driver dwmmc_k3 requests probe deferral
[ 5.097402] sdhci-pltfm: SDHCI platform and OF driver helper
[ 5.104029] ledtrig-cpu: registered to indicate activity on CPUs
[ 5.110354] usbcore: registered new interface driver usbhid
[ 5.115968] usbhid: USB HID core driver
[ 5.119947] u32 classifier
[ 5.122655] Actions configured
[ 5.126136] Netfilter messages via NETLINK v0.30.
[ 5.130941] nf_conntrack version 0.5.0 (7036 buckets, 28144 max)
[ 5.137310] ctnetlink v0.93: registering with nfnetlink.
[ 5.143654] xt_time: kernel timezone is -0000
[ 5.148422] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 5.153960] arp_tables: (C) 2002 David S. Miller
[ 5.158745] TCP: cubic registered
[ 5.162103] Initializing XFRM netlink socket
[ 5.166495] NET: Registered protocol family 10
[ 5.171736] mip6: Mobile IPv6
[ 5.174755] ip6_tables: (C) 2000-2006 Netfilter Core Team
[ 5.180465] NET: Registered protocol family 17
[ 5.184959] NET: Registered protocol family 15
[ 5.189500] 9pnet: Installing 9P2000 support
[ 5.193882] Key type dns_resolver registered
[ 5.199108] registered taskstats version 1
[ 5.203921] Btrfs loaded
[ 5.207077] uart-pl011 f7111000.uart: ttyAMA1 at MMIO 0xf7111000
(irq = 69, base_baud = 0) is a PL011 rev2
[ 5.217330] uart-pl011 f7112000.uart: ttyAMA2 at MMIO 0xf7112000
(irq = 70, base_baud = 0) is a PL011 rev2
[ 5.227461] uart-pl011 f7113000.uart: aliased and non-aliased
serial devices found in device tree. Serial port enumeration may be
unpredictable.
[ 5.240503] uart-pl011 f7113000.uart: ttyAMA3 at MMIO 0xf7113000
(irq = 71, base_baud = 0) is a PL011 rev2
[ 5.250524] uart-pl011 f7114000.uart: aliased and non-aliased
serial devices found in device tree. Serial port enumeration may be
unpredictable.
[ 5.263551] uart-pl011 f7114000.uart: ttyAMA4 at MMIO 0xf7114000
(irq = 72, base_baud = 0) is a PL011 rev2
[ 5.273555] fixed_5v_hub: 5000 mV
[ 5.277167] wlan-en-regulator: 1800 mV
[ 5.284517] usb 1-1: not running at top speed; connect to a high speed hub
[ 5.292146] hub 1-1:1.0: USB hub found
[ 5.293304] [drm] HDMI: status=1,hpd=1,dpms=3
[ 5.300443] hub 1-1:1.0: 3 ports detected
[ 5.314423] [drm]
mipi_init,pixcel_clk=75,lane_byte_clk=80,hsa=42,hbp=117,hline=1760
[ 5.314425] [drm] mipi_init , exit success!
[ 5.333965] Console: switching to colour frame buffer device 160x45
[ 5.367052] hisi-drm smb:display-subsystem: fb0: frame buffer device
[ 5.373614] hisi-drm smb:display-subsystem: registered panic notifier
[ 5.436020] dwmmc_k3 f723f000.dwmmc2: fifo-depth property not
found, using value of FIFOTH register as default
[ 5.446409] dwmmc_k3 f723f000.dwmmc2: Using internal DMA controller.
[ 5.452886] dwmmc_k3 f723f000.dwmmc2: Version ID is 250a
[ 5.458328] dwmmc_k3 f723f000.dwmmc2: DW MMC controller at irq 106,
32 bit host data width, 64 deep fifo
[ 5.468115] dwmmc_k3 f723f000.dwmmc2: No vqmmc regulator found
[ 5.574539] mmc_host mmc2: Bus speed (slot 0) = 25000000Hz (slot
req 400000Hz, actual 390625HZ div = 32)
[ 5.574580] usb 1-1.2: new low-speed USB device number 3 using dwc2
[ 5.604256] dwmmc_k3 f723f000.dwmmc2: 1 slots initialized
[ 5.610676] dwmmc_k3 f723f000.dwmmc2: card claims to support
voltages below defined range
[ 5.619202] rtc-pl031 f8003000.rtc: setting system clock to
1970-01-01 00:00:17 UTC (17)
[ 5.620385] mmc_host mmc2: Bus speed (slot 0) = 25000000Hz (slot
req 25000000Hz, actual 25000000HZ div = 0)
[ 5.621814] mmc2: queuing unknown CIS tuple 0x91 (3 bytes)
[ 5.623123] mmc2: new SDIO card at address 0001
[ 5.671733] SOC_MED: disabling
[ 5.678756] G3D_PD_VDD: disabling
[ 5.686123] ALSA device list:
[ 5.692973] No soundcards found.
[ 5.700365] of_dma_request_slave_channel: dma-names property of
node '/smb/uart@f8015000' missing or empty
[ 5.714016] uart-pl011 f8015000.uart: no DMA platform data
[ 5.723595] Freeing unused kernel memory: 356K (ffffffc000af2000 -
ffffffc000b4b000)
[ 5.735664] input: Chicony USB Keyboard as
/devices/f72c0000.usb/usb1/1-1/1-1.2/1-1.2:1.0/0003:04F2:0402.0001/input/input0
Loading, please wait...
[ 5.751060] hid-generic 0003:04F2:0402.0001: input: USB HID v1.11
Keyboard [Chicony USB Keyboard] on usb-f72c0000.usb-1.2/input0
[ 5.770040] systemd-udevd[946]: starting version 215
[ 5.783695] random: systemd-udevd urandom read with 12 bits of
entropy available
[ 5.789690] input: Chicony USB Keyboard as
/devices/f72c0000.usb/usb1/1-1/1-1.2/1-1.2:1.1/0003:04F2:0402.0002/input/input1
[ 5.789879] hid-generic 0003:04F2:0402.0002: input: USB HID v1.11
Device [Chicony USB Keyboard] on usb-f72c0000.usb-1.2/input1
[ 5.944610] usb usb1: clear tt 1 (8020) error -22
[ 6.034658] usb 1-1.1: new low-speed USB device number 4 using dwc2
[ 6.084649] usb usb1: clear tt 1 (8020) error -22
[ 6.154586] usb usb1: clear tt 1 (0020) error -22
[ 6.197375] input: USB Optical Mouse as
/devices/f72c0000.usb/usb1/1-1/1-1.1/1-1.1:1.0/0003:15CA:00C3.0003/input/input2
[ 6.214013] hid-generic 0003:15CA:00C3.0003: input: USB HID v1.10
Mouse [USB Optical Mouse] on usb-f72c0000.usb-1.1/input0
Begin: Loading essential drivers ... done.
Begin: Running /scripts/init-premount ... done.
Begin: Mounting root file system ... Begin: Running /scripts/local-top ... done.
Begin: Running /scripts/local-premount ... Scanning for Btrfs filesystems
done.
Begin: Waiting for root file system ... [ 6.784296] [drm] HDMI: hpd work in
[ 6.813780] [drm] HDMI: hpd_event_sent=0
[ 6.843405] [drm] HDMI: hpd work out
Begin: Running /scripts/local-block ... done.
Begin: Running /scripts/local-block ... done.
Begin: Running /scripts/local-block ... done.
[ 9.726745] random: nonblocking pool is initialized
Begin: Running /scripts/local-block ... done.
Begin: Running /scripts/local-block ... done.
Begin: Running /scripts/local-block ... done.
Begin: Running /scripts/local-block ... done.
Begin: Running /scripts/local-block ... done.
Begin: Running /scripts/local-block ... done.
Begin: Running /scripts/local-block ... done.
Begin: Running /scripts/local-block ... done.
Begin: Running /scripts/local-block ... done.
Begin: Running /scripts/local-block ... done.
Begin: Running /scripts/local-block ... done.
Begin: Running /scripts/local-block ... done.
Begin: Running /scripts/local-block ... done.
Begin: Running /scripts/local-block ... done.
Begin: Running /scripts/local-block ... done.
Begin: Running /scripts/local-block ... done.
Begin: Running /scripts/local-block ... done.
Begin: Running /scripts/local-block ... done.
Begin: Running /scripts/local-block ... done.
Begin: Running /scripts/local-block ... done.
Begin: Running /scripts/local-block ... done.
Begin: Running /scripts/local-block ... done.
Begin: Running /scripts/local-block ... done.
Begin: Running /scripts/local-block ... done.
Begin: Running /scripts/local-block ... done.
Begin: Running /scripts/local-block ... done.
Begin: Running /scripts/local-block ... done.
done.
Gave up waiting for root device. Common problems:
- Boot args (cat /proc/cmdline)
- Check rootdelay= (did the system wait long enough?)
- Check root= (did the system wait for the right device?)
- Missing modules (cat /proc/modules; ls /dev)
ALERT! /dev/mmcblk1p2 does not exist. Dropping to a shell!

(initramfs) cat /proc/cmdline
iommu_ddr_size=0x40000000 console=tty0 console=ttyAMA0,115200n8
root=/dev/mmcblk1p2 rootwait rw
mem=908M boardid=0x48696220,0x00000011,0x0000002b
thermal_trim=0x9a492400 pd_charge=0 boottype=defaultnormal
enter_recovery=0 androidboot.swtype=normal fastboot_version=
himntn=111111111111111111

(initramfs) ls /dev/mmc*
brw------- 1 0 0 179, 0 /dev/mmcblk0
brw------- 1 0 0 179, 64 /dev/mmcblk0boot0
brw------- 1 0 0 179,128 /dev/mmcblk0boot1
brw------- 1 0 0 179, 1 /dev/mmcblk0p1
brw------- 1 0 0 179, 2 /dev/mmcblk0p2
brw------- 1 0 0 179, 3 /dev/mmcblk0p3
brw------- 1 0 0 179, 4 /dev/mmcblk0p4
brw------- 1 0 0 179, 5 /dev/mmcblk0p5
brw------- 1 0 0 179, 6 /dev/mmcblk0p6
brw------- 1 0 0 179, 7 /dev/mmcblk0p7
brw------- 1 0 0 179, 8 /dev/mmcblk0p8
brw------- 1 0 0 179, 9 /dev/mmcblk0p9

On 3 October 2015 at 17:07, Fathi Boudra <fathi.boudra@linaro.org> wrote:
> On 3 October 2015 at 16:06, Lee Jones <lee.jones@linaro.org> wrote:
>> After following the instructions in the Quick Start Guide for booting
>> from SD card I receive:
>>
>> [tux.img][tux.img][tux.img][tux.img][tux.img][tux.img][tux.img][tux.img]
>> [STAMP] kvm [1]: HYP mode not available
>> [STAMP] of_dma_request_slave_channel: dma-names property of node
>> '/smb/uart@f8015000' missing or empty
>> [STAMP] hisi_thermal f7030700.tsensor: THERMAL ALARM: T > 80
>> <DEAD>
>>
>> Has anyone else seen this? Is it a known issue, or all-my-fault(tm)?
>
> there's a known issue in the latest builds however build #323 should work.
> https://bugs.96boards.org/show_bug.cgi?id=100
>
>> NB: This is 'hikey-jessie_alip_20150701-323.img'. Booting
>> 'hikey-jessie_developer_20150701-323.emmc.img' from eMMC works fine.
>>
>> Kind regards,
>> Lee
>
> Cheers,
> Fathi

--
Lee Jones
Linaro ST Landing Team Lead
Linaro.org │ Open source software for ARM SoCs
Follow Linaro: Facebook | Twitter | Blog

_______________________________________________
Dev mailing list
Dev@lists.96boards.org
https://lists.96boards.org/mailman/listinfo/dev