Hi Daniel,
Can you share the logcat output as well ?
Thanks for the fast reply.
Yes i copied the files gralloc.hikey.so + libGLES_mali.so from ../vendor/vendor/mali/64bit
into the ../android/ folder where i built the AOSP.
Am Dienstag, 01. Dezember 2015 12:40 CET, Vishal Bhoj <vishal.bhoj@linaro.org> schrieb:
> Hi Daniel,
>
>
> Did you download and extract vendor.tar.bz2 in AOSP source tree:
> http://builds.96boards.org/snapshots/hikey/linaro/binaries/20150706/vendor.tar.bz2
>
> On 1 December 2015 at 17:05, Daniel Schneider <
> Daniel.Schneider1@hs-augsburg.de> wrote:
>
> > Hi,
> >
> > The goal is to be able to run my own AOSP RPB Builds
> > However i've got problems at running my own CE AOSP RPB HiKey Build with
> > the instructions from the wiki [1]:
> > Note: Installing and booting the pre-build binaries works fine.
> > I first tried to build the AOSP Images with the Instructions from [1] and
> > used it with the self built bootloader files from [3].
> > Building AOSP and the bootloader files was successful, so was flashing on
> > the Hikey Board acc. to[3] + [2]. It then
> > started booting but did not boot correctly into Android but instead showed
> > the following log message during boot:
> >
> >
> > [ 6.433602] EXT4-fs (mmcblk0p9): mounted filesystem with ordered data
> > mode. Opts: (null)
> > [ 6.442000] fs_mgr:
> > __mount(source=/dev/block/platform/f723d000.dwmmc0/by-name/system,target=/system,type=ext4)=0
> > [ 6.487806] EXT4-fs (mmcblk0p8): mounting with "discard" option, but
> > the device does not support discard
> > [ 6.497310] EXT4-fs (mmcblk0p8): mounted filesystem with ordered data
> > mode. Opts: discard,noauto_da_alloc,data=ordered,user_xatt1
> > [ 6.510642] fs_mgr:
> > __mount(source=/dev/block/platform/f723d000.dwmmc0/by-name/cache,target=/cache,type=ext4)=0
> > [ 6.556490] EXT4-fs (mmcblk0p10): mounting with "discard" option, but
> > the device does not support discard
> > [ 6.566146] EXT4-fs (mmcblk0p10): mounted filesystem with ordered data
> > mode. Opts: discard,noauto_da_alloc,data=ordered,user_xat1
> > [ 6.579670] fs_mgr:
> > __mount(source=/dev/block/platform/f723d000.dwmmc0/by-name/userdata,target=/data,type=ext4)=0
> > [ 6.591402] file system registered
> > [ 6.596261] init: Starting service 'adbd'...
> > [ 6.605118] read descriptors
> > [ 6.605180] init: Starting service 'logd'...
> > [ 6.612277] read strings
> > [ 6.655015] rfkill: version magic '3.18.0+ SMP preempt mod_unload
> > aarch64' should be '3.18.0+ SMP preempt aarch64'
> > [ 6.670410] compat: version magic '3.18.0+ SMP preempt mod_unload
> > aarch64' should be '3.18.0+ SMP preempt aarch64'
> > [ 6.729645] cfg80211: version magic '3.18.0+ SMP preempt mod_unload
> > aarch64' should be '3.18.0+ SMP preempt aarch64'
> > [ 6.796284] mac80211: version magic '3.18.0+ SMP preempt mod_unload
> > aarch64' should be '3.18.0+ SMP preempt aarch64'
> > [ 6.845168] wlcore: version magic '3.18.0+ SMP preempt mod_unload
> > aarch64' should be '3.18.0+ SMP preempt aarch64'
> > [ 6.864117] logd.auditd: start
> > [ 6.872944] wl18xx: version magic '3.18.0+ SMP preempt mod_unload
> > aarch64' should be '3.18.0+ SMP preempt aarch64'
> > [ 6.886715] wlcore_sdio: version magic '3.18.0+ SMP preempt mod_unload
> > aarch64' should be '3.18.0+ SMP preempt aarch64'
> > [ 7.162376] bluetooth: version magic '3.18.0+ SMP preempt mod_unload
> > aarch64' should be '3.18.0+ SMP preempt aarch64'
> > [ 7.206857] hidp: version magic '3.18.0+ SMP preempt mod_unload
> > aarch64' should be '3.18.0+ SMP preempt aarch64'
> > [ 7.266267] rfcomm: version magic '3.18.0+ SMP preempt mod_unload
> > aarch64' should be '3.18.0+ SMP preempt aarch64'
> > [ 7.304858] st_drv: version magic '3.18.0+ SMP preempt mod_unload
> > aarch64' should be '3.18.0+ SMP preempt aarch64'
> > [ 7.315514] (stk) : timed out waiting for ldisc to be un-installed
> > [ 7.333862] tty_hci: version magic '3.18.0+ SMP preempt mod_unload
> > aarch64' should be '3.18.0+ SMP preempt aarch64'
> > [ 7.361656] btwilink: version magic '3.18.0+ SMP preempt mod_unload
> > aarch64' should be '3.18.0+ SMP preempt aarch64'
> > [ 7.428522] (stk) :ldisc_install = 1
> > [ 7.440337] gator: version magic '3.18.0+ SMP preempt mod_unload
> > aarch64' should be '3.18.0+ SMP preempt aarch64'
> > [ 7.457707] init: Starting service 'vold'...
> > [ 7.465446] init: Not bootcharting.
> >
> > Then I built AOSP for Android 6.0 by making the following changes to the
> > build instructions :
> > I used the branch android-6.0.0.r1 (instead of android-5.1.1._r1) for the
> > repo init and android-6.0 (instead of android-5.0) for the local_manifest.
> > I also
> > used the bootloader files from my own build. This time the log message
> > during boot was:
> >
> > [ 6.441490] EXT4-fs (mmcblk0p9): mounted filesystem with ordered data
> > mode. Opts: (null)
> > [ 6.449859] fs_mgr:
> > __mount(source=/dev/block/platform/f723d000.dwmmc0/by-name/system,target=/system,type=ext4)=0
> > [ 6.596897] EXT4-fs (mmcblk0p8): recovery complete
> > [ 6.603855] EXT4-fs (mmcblk0p8): mounting with "discard" option, but
> > the device does not support discard
> > [ 6.613491] EXT4-fs (mmcblk0p8): mounted filesystem with ordered data
> > mode. Opts: discard,noauto_da_alloc,data=ordered,user_xatt1
> > [ 6.626964] fs_mgr:
> > __mount(source=/dev/block/platform/f723d000.dwmmc0/by-name/cache,target=/cache,type=ext4)=0
> > [ 6.726001] random: nonblocking pool is initialized
> > [ 7.305400] (stk) : timed out waiting for ldisc to be un-installed
> > [ 7.418574] (stk) :ldisc_install = 1[ 7.735815] EXT4-fs
> > (mmcblk0p10): recovery complete
> > [ 7.742897] EXT4-fs (mmcblk0p10): mounting with "discard" option, but
> > the device does not support discard
> > [ 7.752645] EXT4-fs (mmcblk0p10): mounted filesystem with ordered data
> > mode. Opts: discard,noauto_da_alloc,data=ordered,user_xat1
> > [ 7.766184] fs_mgr:
> > __mount(source=/dev/block/platform/f723d000.dwmmc0/by-name/userdata,target=/data,type=ext4)=0
> > [ 7.777627] file system registered
> > [ 7.782144] init: Starting service 'adbd'...
> > [ 7.791612] read descriptors
> > [ 7.791990] init: Starting service 'logd'...
> > [ 7.798827] read strings
> > [ 7.812920] Loading modules backported from Linux version 3cf1c17
> > [ 7.819068] Backport generated by backports.git 5394a1d
> > [ 7.856620] cfg80211: Calling CRDA to update world regulatory domain
> > [ 7.956810] init: Starting service 'vold'...
> > [ 7.962186] init: Not bootcharting.
> > [ 7.967196] wl18xx_driver wl18xx.0.auto: Direct firmware load for
> > ti-connectivity/wl1271-nvs.bin failed with error -2
> > [ 7.977844] wl18xx_driver wl18xx.0.auto: Falling back to user helper
> > [ 7.990973] init: Starting service 'exec 0 (/system/bin/tzdatacheck)'...
> > [ 8.082339] init: Service 'exec 0 (/system/bin/tzdatacheck)' (pid 1478)
> > exited with status 0
> > [ 8.083243] logd.auditd: start
> > [ 8.083361] logd.klogd: 8078974165
> > [ 8.099467] init: SELinux: Could not get canonical path
> > /data/local/tmp/lava restorecon: No such file or directory.
> > [ 8.118620] init: property_set("ro.secure", "0") failed
> > [ 8.124122] init: (Loading properties from /system/build.prop took
> > 0.01s.)
> > [ 8.131149] init: (Loading properties from /vendor/build.prop took
> > 0.00s.)
> > [ 8.138098] init: (Loading properties from /factory/factory.prop took
> > 0.00s.)
> > [ 8.145335] init: (Loading properties from /data/local.prop took 0.00s.)
> > [ 8.152256] init: /recovery not specified in fstab
> > [ 8.157346] init: Starting service 'logd-reinit'...
> > [ 8.164797] init: Starting service 'healthd'...
> > [ 8.170030] init: Starting service 'lmkd'...
> > [ 8.171893] binder: 1489:1489 transaction failed 29189, size 0-0
> > [ 8.177075] logd.daemon: reinit
> > [ 8.184277] init: Starting service 'servicemanager'...
> > [ 8.186238] wl18xx_driver wl18xx.0.auto: Direct firmware load for
> > ti-connectivity/wl18xx-conf.bin failed with error -2
> > [ 8.186242] wl18xx_driver wl18xx.0.auto: Falling back to user helper
> > [ 8.187620] wlcore: ERROR could not get configuration binary
> > ti-connectivity/wl18xx-conf.bin: -11
> > [ 8.187623] wlcore: WARNING falling back to default config
> > [ 8.221811] init: Starting service 'surfaceflinger'...
> > [ 8.227444] init: Service 'logd-reinit' (pid 1488) exited with status 0
> > [ 8.234266] init: property_set("ro.build.product", "generic") failed
> > [ 8.241015] init: property_set("ro.product.device", "generic") failed
> > [ 8.248542] init: Starting service 'console'...
> > [ 8.253876] init: Starting service 'netd'...
> > [ 8.258852] init: Starting service 'debuggerd'...
> > [ 8.264117] init: Starting service 'debuggerd64'...
> > [ 8.269429] init: cannot find '/system/bin/rild', disabling 'ril-daemon'
> > [ 8.276521] init: Starting service 'drm'...
> > [ 8.281427] init: Starting service 'media'...
> > [ 8.286577] init: Starting service 'installd'...
> > [ 8.291567] init: cannot find '/system/bin/install-recovery.sh',
> > disabling 'flash_recovery'
> > [ 8.300353] init: Starting service 'keystore'...
> > [ 8.305671] init: Starting service 'uim'...
> > [ 8.310546] init: Starting service 'zygote'...
> > [ 8.315682] init: Starting service 'zygote_secondary'...
> > [ 8.321742] init: Starting service 'gatekeeperd'...
> > [ 8.324669] of_dma_request_slave_channel: dma-names property of node
> > '/smb/uart@f7111000' missing or empty
> > [ 8.324679] uart-pl011 f7111000.uart: no DMA platform data
> > [ 8.349327] init: Starting service 'perfprofd'...
> > [ 8.375151] (stc): st_tty_open
> > [ 8.378183] (stk) :line discipline installed(stk)
> > :ti-connectivity/TIInit_11.8.32.bts
> > [ 8.391144] (stk) :change remote baud rate command in firmware(stk)
> > :skipping the wait event of change remote baud
> > [ 8.445038] wlcore: wl18xx HW: 183x or 180x, PG 2.2 (ROM 0x11)
> > [ 8.455602] wlcore: loaded
> > [ 8.458358] wlcore: driver version:
> > [ 8.461934] wlcore: compilation time: 11:54, Beijing, 09-Apr-2015
> > shell@hikey:/ $ [ 9.127873] (stc): add_channel_to_table: id 4
> > [ 9.132244] (stc): add_channel_to_table: id 2
> > [ 9.136627] (stc): add_channel_to_table: id 3
> > [ 9.173303] healthd: No charger supplies found
> > [ 9.177832] healthd: No battery devices found
> > [ 9.356078] init: Service 'surfaceflinger' (pid 1497) killed by signal 6
> > [ 9.362814] init: Service 'surfaceflinger' (pid 1497) killing any
> > children in process group
> > [ 9.371245] init: Service 'zygote' is being killed...
> > [ 9.379745] dwc2 f72c0000.usb: bound driver configfs-gadget
> > [ 9.388709] init: Service 'zygote' (pid 1557) killed by signal 9
> > [ 9.394794] init: Service 'zygote' (pid 1557) killing any children in
> > process group
> > [ 9.402579] init: write_file: Unable to open
> > '/sys/android_power/request_state': No such file or directory
> > [ 9.412366] init: write_file: Unable to write to '/sys/power/state':
> > Invalid argument
> > [ 9.420311] init: Service 'media' is being killed...
> > [ 9.425456] init: Service 'netd' is being killed...
> > [ 9.430625] init: Service 'media' (pid 1546) killed by signal 9
> > [ 9.436643] init: Service 'media' (pid 1546) killing any children in
> > process group
> > [ 9.444371] init: Service 'netd' (pid 1542) killed by signal 9
> > [ 9.450230] init: Service 'netd' (pid 1542) killing any children in
> > process group
> > [ 9.457996] init: Untracked pid 1673 killed by signal 9
> > [ 9.466537] dwc2 f72c0000.usb: bound driver configfs-gadget
> > [ 9.475254] init: write_file: Unable to open
> > '/sys/class/android_usb/android0/enable': No such file or directory
> > [ 9.485465] init: write_file: Unable to open
> > '/sys/class/android_usb/android0/idVendor': No such file or directory
> > [ 9.495870] init: write_file: Unable to open
> > '/sys/class/android_usb/android0/idProduct': No such file or directory
> > [ 9.506401] init: write_file: Unable to open
> > '/sys/class/android_usb/android0/functions': No such file or directory
> > [ 9.516908] init: write_file: Unable to open
> > '/sys/class/android_usb/android0/enable': No such file or directory
> > [ 9.527236] init: write_file: Unable to write to
> > '/sys/kernel/config/usb_gadget/g1/UDC': Device or resource busy
> > [ 9.540650] dwc2 f72c0000.usb: bound driver configfs-gadget
> > [ 9.767073] dwc2 f72c0000.usb: new device is high-speed
> > [ 9.879422] dwc2 f72c0000.usb: new device is high-speed
> > [ 9.936162] dwc2 f72c0000.usb: new address 9
> > [ 9.959138] configfs-gadget gadget: high-speed config #1: c
> > [ 11.144699] (stc): remove_channel_from_table: id 3
> > [ 11.149520] (stc): remove_channel_from_table: id 2
> > [ 11.154316] (stc): remove_channel_from_table: id 4
> > [ 11.159179] (stc): all chnl_ids unregistered
> > [ 11.163474] (stk) :ldisc_install = 0(stc): st_tty_close
> > [ 12.175454] (hci_tty): called dumb_hci_callback
> > [ 13.553970] init: Starting service 'netd'...
> > [ 13.559074] init: Starting service 'surfaceflinger'...
> > [ 13.565316] init: Starting service 'media'...
> > [ 13.570388] init: Starting service 'zygote'...
> > [ 13.720157] init: Service 'surfaceflinger' (pid 1679) killed by signal 6
> > [ 13.726955] init: Service 'surfaceflinger' (pid 1679) killing any
> > children in process group
> > [ 13.735408] init: Service 'zygote' is being killed...
> > [ 13.743204] init: Service 'zygote' (pid 1683) killed by signal 9
> > [ 13.749314] init: Service 'zygote' (pid 1683) killing any children in
> > process group
> > [ 13.757137] init: write_file: Unable to open
> > '/sys/android_power/request_state': No such file or directory
> > [ 13.766965] init: write_file: Unable to write to '/sys/power/state':
> > Invalid argument
> > [ 13.774928] init: Service 'media' is being killed...
> > [ 13.779999] init: Service 'netd' is being killed...
> > [ 13.785208] init: Service 'media' (pid 1680) killed by signal 9
> > [ 13.791197] init: Service 'media' (pid 1680) killing any children in
> > process group
> > [ 13.799067] init: Service 'netd' (pid 1678) killed by signal 9
> > [ 13.804960] init: Service 'netd' (pid 1678) killing any children in
> > process group
> > [ 13.812752] init: Untracked pid 1710 killed by signal 9
> >
> >
> > So i'd like to know/ need some help what AOSP Build Instruction to follow
> > to be able to build and run Android 6.0 from source.
> >
> >
> >
> > Regards,
> >
> > Daniel
> >
> >
> > [1]
> > https://github.com/96boards/documentation/wiki/CE-AOSP-RPB-HiKey-15.10-Build
> >
> > [2]
> > https://github.com/96boards/documentation/wiki/CE-AOSP-RPB-HiKey-15.10-Install
> >
> > [3] https://github.com/96boards/documentation/wiki/HiKeyUEFI
> >
> > _______________________________________________
> > Dev mailing list
> > Dev@lists.96boards.org
> > https://lists.96boards.org/mailman/listinfo/dev
> >