Add initial device tree support for Variscite DART-SD410 Evalueation board. This board is also known as VAR-SD410CustomBoard.

Signed-off-by: Leonid Segal leonid.s@variscite.com --- arch/arm64/boot/dts/qcom/Makefile | 1 + .../boot/dts/qcom/apq8016-var-dart-pmic-pins.dtsi | 53 +++ .../boot/dts/qcom/apq8016-var-dart-soc-pins.dtsi | 88 ++++ arch/arm64/boot/dts/qcom/apq8016-var-dart.dts | 21 + arch/arm64/boot/dts/qcom/apq8016-var-dart.dtsi | 525 +++++++++++++++++++++ 5 files changed, 688 insertions(+) create mode 100644 arch/arm64/boot/dts/qcom/apq8016-var-dart-pmic-pins.dtsi create mode 100644 arch/arm64/boot/dts/qcom/apq8016-var-dart-soc-pins.dtsi create mode 100644 arch/arm64/boot/dts/qcom/apq8016-var-dart.dts create mode 100644 arch/arm64/boot/dts/qcom/apq8016-var-dart.dtsi

diff --git a/arch/arm64/boot/dts/qcom/Makefile b/arch/arm64/boot/dts/qcom/Makefile index cc0f02d9dd02..0cf2fa44d96a 100644 --- a/arch/arm64/boot/dts/qcom/Makefile +++ b/arch/arm64/boot/dts/qcom/Makefile @@ -4,6 +4,7 @@ dtb-$(CONFIG_ARCH_QCOM) += msm8916-mtp.dtb dtb-$(CONFIG_ARCH_QCOM) += msm8992-bullhead-rev-101.dtb dtb-$(CONFIG_ARCH_QCOM) += msm8994-angler-rev-101.dtb dtb-$(CONFIG_ARCH_QCOM) += msm8996-mtp.dtb +dtb-$(CONFIG_ARCH_QCOM) += apq8016-var-dart.dtb

always := $(dtb-y) subdir-y := $(dts-dirs) diff --git a/arch/arm64/boot/dts/qcom/apq8016-var-dart-pmic-pins.dtsi b/arch/arm64/boot/dts/qcom/apq8016-var-dart-pmic-pins.dtsi new file mode 100644 index 000000000000..d94640812194 --- /dev/null +++ b/arch/arm64/boot/dts/qcom/apq8016-var-dart-pmic-pins.dtsi @@ -0,0 +1,53 @@ +#include <dt-bindings/pinctrl/qcom,pmic-gpio.h> +#include <dt-bindings/pinctrl/qcom,pmic-mpp.h> + +&pm8916_gpios { + + usb_hub_reset_pm: usb_hub_reset_pm { + pinconf { + pins = "gpio3"; + function = PMIC_GPIO_FUNC_NORMAL; + output-low; + }; + }; + + usb_sw_sel_pm: usb_sw_sel_pm { + pinconf { + pins = "gpio4"; + function = PMIC_GPIO_FUNC_NORMAL; + power-source = <PM8916_GPIO_VPH>; + input-disable; + }; + }; + + pm8916_gpios_leds: pm8916_gpios_leds { + pinconf { + pins = "gpio1", "gpio2"; + function = PMIC_GPIO_FUNC_NORMAL; + output-low; + }; + }; +}; + +&pm8916_mpps { + + pinctrl-names = "default"; + pinctrl-0 = <&ls_exp_gpio_f>; + + ls_exp_gpio_f: pm8916_mpp4 { + pinconf { + pins = "mpp4"; + function = "digital"; + output-low; + power-source = <PM8916_MPP_L5>; // 1.8V + }; + }; + + pm8916_mpps_leds: pm8916_mpps_leds { + pinconf { + pins = "mpp2", "mpp3"; + function = "digital"; + output-low; + }; + }; +}; diff --git a/arch/arm64/boot/dts/qcom/apq8016-var-dart-soc-pins.dtsi b/arch/arm64/boot/dts/qcom/apq8016-var-dart-soc-pins.dtsi new file mode 100644 index 000000000000..185388de914c --- /dev/null +++ b/arch/arm64/boot/dts/qcom/apq8016-var-dart-soc-pins.dtsi @@ -0,0 +1,88 @@ + +#include <dt-bindings/gpio/gpio.h> + +&msmgpio { + + msmgpio_leds: msmgpio_leds { + pinconf { + pins = "gpio21", "gpio120"; + function = "gpio"; + output-low; + }; + }; + + usb_id_default: usb-id-default { + pinmux { + function = "gpio"; + pins = "gpio121"; + }; + + pinconf { + pins = "gpio121"; + drive-strength = <8>; + input-enable; + bias-pull-up; + }; + }; + + adv7533_int_active: adv533_int_active { + pinmux { + function = "gpio"; + pins = "gpio31"; + }; + pinconf { + pins = "gpio31"; + drive-strength = <16>; + bias-disable; + }; + }; + + adv7533_int_suspend: adv7533_int_suspend { + pinmux { + function = "gpio"; + pins = "gpio31"; + }; + pinconf { + pins = "gpio31"; + drive-strength = <2>; + bias-disable; + }; + }; + + adv7533_switch_active: adv7533_switch_active { + pinmux { + function = "gpio"; + pins = "gpio32"; + }; + pinconf { + pins = "gpio32"; + drive-strength = <16>; + bias-disable; + }; + }; + + adv7533_switch_suspend: adv7533_switch_suspend { + pinmux { + function = "gpio"; + pins = "gpio32"; + }; + pinconf { + pins = "gpio32"; + drive-strength = <2>; + bias-disable; + }; + }; + + msm_key_volp_n_default: msm_key_volp_n_default { + pinmux { + function = "gpio"; + pins = "gpio107"; + }; + pinconf { + pins = "gpio107"; + drive-strength = <8>; + input-enable; + bias-pull-up; + }; + }; +}; diff --git a/arch/arm64/boot/dts/qcom/apq8016-var-dart.dts b/arch/arm64/boot/dts/qcom/apq8016-var-dart.dts new file mode 100644 index 000000000000..7ea8eaa2754a --- /dev/null +++ b/arch/arm64/boot/dts/qcom/apq8016-var-dart.dts @@ -0,0 +1,21 @@ +/* + * Copyright (c) 2015, The Linux Foundation. All rights reserved. + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 and + * only version 2 as published by the Free Software Foundation. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + */ + +/dts-v1/; + +#include "apq8016-var-dart.dtsi" + +/ { + model = "Variscite LTD. VAR-DART410"; + compatible = "qcom,apq8016-dart", "qcom,apq8016", "qcom,dart"; +}; diff --git a/arch/arm64/boot/dts/qcom/apq8016-var-dart.dtsi b/arch/arm64/boot/dts/qcom/apq8016-var-dart.dtsi new file mode 100644 index 000000000000..f214d0b101a4 --- /dev/null +++ b/arch/arm64/boot/dts/qcom/apq8016-var-dart.dtsi @@ -0,0 +1,525 @@ +/* + * Copyright (c) 2015, The Linux Foundation. All rights reserved. + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 and + * only version 2 as published by the Free Software Foundation. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + */ + +#include "msm8916.dtsi" +#include "pm8916.dtsi" +#include "apq8016-var-dart-soc-pins.dtsi" +#include "apq8016-var-dart-pmic-pins.dtsi" +#include <dt-bindings/gpio/gpio.h> +#include <dt-bindings/input/input.h> +#include <dt-bindings/sound/apq8016-lpass.h> + +/ { + aliases { + serial0 = &blsp1_uart2; + serial1 = &blsp1_uart1; + usid0 = &pm8916_0; + i2c0 = &blsp_i2c2; + i2c1 = &blsp_i2c6; + i2c3 = &blsp_i2c4; + spi0 = &blsp_spi5; + spi1 = &blsp_spi3; + }; + + chosen { + stdout-path = "serial0"; + }; + + soc { + dma@7884000 { + status = "okay"; + }; + + serial@78af000 { + label = "LS-UART0"; + status = "okay"; + pinctrl-names = "default", "sleep"; + pinctrl-0 = <&blsp1_uart1_default>; + pinctrl-1 = <&blsp1_uart1_sleep>; + }; + + serial@78b0000 { + label = "LS-UART1"; + status = "okay"; + pinctrl-names = "default", "sleep"; + pinctrl-0 = <&blsp1_uart2_default>; + pinctrl-1 = <&blsp1_uart2_sleep>; + }; + + i2c@78b6000 { + /* On Low speed expansion */ + label = "LS-I2C0"; + status = "okay"; + }; + + i2c@78b8000 { + /* On High speed expansion */ + label = "HS-I2C2"; + status = "okay"; + + adv_bridge: bridge@39 { + status = "okay"; + + compatible = "adi,adv7533"; + reg = <0x39>; + + interrupt-parent = <&msmgpio>; + interrupts = <31 2>; + + adi,dsi-lanes = <4>; + + pd-gpios = <&msmgpio 32 0>; + + avdd-supply = <&pm8916_l6>; + v1p2-supply = <&pm8916_l6>; + v3p3-supply = <&pm8916_l17>; + + pinctrl-names = "default","sleep"; + pinctrl-0 = <&adv7533_int_active>, + <&adv7533_switch_active>; + pinctrl-1 = <&adv7533_int_suspend>, + <&adv7533_switch_suspend>; + #sound-dai-cells = <1>; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + adv7533_in: endpoint { + remote-endpoint = <&dsi0_out>; + }; + }; + + port@1 { + reg = <1>; + adv7533_out: endpoint { + remote-endpoint = <&hdmi_con>; + }; + }; + }; + }; + }; + + i2c@78ba000 { + /* On Low speed expansion */ + label = "LS-I2C1"; + status = "okay"; + }; + + spi@78b7000 { + /* On High speed expansion */ + label = "HS-SPI1"; + status = "okay"; + }; + + spi@78b9000 { + /* On Low speed expansion */ + label = "LS-SPI0"; + status = "okay"; + }; + + leds { + pinctrl-names = "default"; + pinctrl-0 = <&msmgpio_leds>, + <&pm8916_gpios_leds>, + <&pm8916_mpps_leds>; + + compatible = "gpio-leds"; + + led@1 { + label = "apq8016-sbc:green:user1"; + gpios = <&msmgpio 21 GPIO_ACTIVE_HIGH>; + linux,default-trigger = "heartbeat"; + default-state = "off"; + }; + + led@2 { + label = "apq8016-sbc:green:user2"; + gpios = <&msmgpio 120 GPIO_ACTIVE_HIGH>; + linux,default-trigger = "mmc0"; + default-state = "off"; + }; + + led@3 { + label = "apq8016-sbc:green:user3"; + gpios = <&pm8916_gpios 1 GPIO_ACTIVE_HIGH>; + linux,default-trigger = "mmc1"; + default-state = "off"; + }; + + led@4 { + label = "apq8016-sbc:green:user4"; + gpios = <&pm8916_gpios 2 GPIO_ACTIVE_HIGH>; + linux,default-trigger = "none"; + default-state = "off"; + }; + + led@5 { + label = "apq8016-sbc:yellow:wlan"; + gpios = <&pm8916_mpps 2 GPIO_ACTIVE_HIGH>; + linux,default-trigger = "phy0rx"; + default-state = "off"; + }; + + led@6 { + label = "apq8016-sbc:blue:bt"; + gpios = <&pm8916_mpps 3 GPIO_ACTIVE_HIGH>; + linux,default-trigger = "hci0-power"; + default-state = "off"; + }; + }; + + sdhci@07824000 { + vmmc-supply = <&pm8916_l8>; + vqmmc-supply = <&pm8916_l5>; + + pinctrl-names = "default", "sleep"; + pinctrl-0 = <&sdc1_clk_on>, + <&sdc1_cmd_on>, + <&sdc1_data_on>; + pinctrl-1 = <&sdc1_clk_off>, + <&sdc1_cmd_off>, + <&sdc1_data_off>; + status = "okay"; + }; + + sdhci@07864000 { + vmmc-supply = <&pm8916_l11>; + vqmmc-supply = <&pm8916_l12>; + + pinctrl-names = "default", "sleep"; + pinctrl-0 = <&sdc2_clk_on>, + <&sdc2_cmd_on>, + <&sdc2_data_on>, + <&sdc2_cd_on>; + pinctrl-1 = <&sdc2_clk_off>, + <&sdc2_cmd_off>, + <&sdc2_data_off>, + <&sdc2_cd_off>; + + cd-gpios = <&msmgpio 38 0x1>; + status = "okay"; + }; + + usb@78d9000 { + extcon = <&usb_id>, <&usb_id>; + status = "okay"; + }; + + ehci@78d9000 { + status = "okay"; + }; + + phy@78d9000 { + v1p8-supply = <&pm8916_l7>; + v3p3-supply = <&pm8916_l13>; + vddcx-supply = <&pm8916_s1>; + extcon = <&usb_id>, <&usb_id>; + dr_mode = "otg"; + status = "okay"; + switch-gpio = <&pm8916_gpios 4 GPIO_ACTIVE_HIGH>; + pinctrl-names = "default"; + pinctrl-0 = <&usb_sw_sel_pm>; + }; + + lpass@07708000 { + status = "okay"; + }; + + mdss@1a00000 { + status = "okay"; + + mdp@1a01000 { + status = "okay"; + }; + + dsi@1a98000 { + status = "okay"; + + vdda-supply = <&pm8916_l2>; + vddio-supply = <&pm8916_l6>; + + ports { + port@1 { + endpoint { + remote-endpoint = <&adv7533_in>; + data-lanes = <0 1 2 3>; + }; + }; + }; + }; + + dsi-phy@1a98300 { + status = "okay"; + + vddio-supply = <&pm8916_l6>; + }; + }; + + lpass_codec: codec{ + status = "okay"; + }; + + sound: sound { + compatible = "qcom,apq8016-sbc-sndcard"; + reg = <0x07702000 0x4>, <0x07702004 0x4>; + reg-names = "mic-iomux", "spkr-iomux"; + + status = "okay"; + pinctrl-0 = <&cdc_pdm_lines_act>, + <&ext_sec_tlmm_lines_act>, + <&ext_mclk_tlmm_lines_act>; + pinctrl-1 = <&cdc_pdm_lines_sus>, + <&ext_sec_tlmm_lines_sus>, + <&ext_mclk_tlmm_lines_sus>; + pinctrl-names = "default", "sleep"; + qcom,model = "DB410c"; + qcom,audio-routing = + "AMIC2", "MIC BIAS Internal2", + "AMIC3", "MIC BIAS External1"; + external-dai-link@0 { + link-name = "ADV7533"; + cpu { /* QUAT */ + sound-dai = <&lpass MI2S_QUATERNARY>; + }; + codec { + sound-dai = <&adv_bridge 0>; + }; + }; + + /* I2S - Internal codec */ + internal-codec-playback-dai-link@0 { + link-name = "WCD"; + cpu { /* PRIMARY */ + sound-dai = <&lpass MI2S_PRIMARY>; + }; + codec { + sound-dai = <&lpass_codec 0>, + <&wcd_codec 0>; + }; + }; + + /* I2S - Internal codec */ + internal-codec-capture-dai-link@0 { + link-name = "WCD-Capture"; + cpu { /* PRIMARY */ + sound-dai = <&lpass MI2S_TERTIARY>; + }; + codec { + sound-dai = <&lpass_codec 1>, + <&wcd_codec 1>; + }; + }; + }; + + wcnss@a21b000 { + status = "okay"; + }; + + camera_vdddo_1v8: fixedregulator@0 { + compatible = "regulator-fixed"; + regulator-name = "camera_vdddo"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-always-on; + }; + + camera_vdda_2v8: fixedregulator@1 { + compatible = "regulator-fixed"; + regulator-name = "camera_vdda"; + regulator-min-microvolt = <2800000>; + regulator-max-microvolt = <2800000>; + regulator-always-on; + }; + + camera_vddd_1v5: fixedregulator@2 { + compatible = "regulator-fixed"; + regulator-name = "camera_vddd"; + regulator-min-microvolt = <1500000>; + regulator-max-microvolt = <1500000>; + regulator-always-on; + }; + }; + + usb2513 { + compatible = "smsc,usb3503"; + reset-gpios = <&pm8916_gpios 3 GPIO_ACTIVE_LOW>; + initial-mode = <1>; + }; + + usb_id: usb-id { + compatible = "linux,extcon-usb-gpio"; + id-gpio = <&msmgpio 121 GPIO_ACTIVE_HIGH>; + pinctrl-names = "default"; + pinctrl-0 = <&usb_id_default>; + }; + + hdmi-out { + compatible = "hdmi-connector"; + type = "a"; + + port { + hdmi_con: endpoint { + remote-endpoint = <&adv7533_out>; + }; + }; + }; + + gpio_keys { + compatible = "gpio-keys"; + #address-cells = <1>; + #size-cells = <0>; + autorepeat; + + pinctrl-names = "default"; + pinctrl-0 = <&msm_key_volp_n_default>; + + button@0 { + label = "Volume Up"; + linux,code = <KEY_VOLUMEUP>; + gpios = <&msmgpio 107 GPIO_ACTIVE_LOW>; + }; + }; +}; + +&blsp_i2c6 { + status = "ok"; +}; + +&wcd_codec { + status = "okay"; + clocks = <&gcc GCC_CODEC_DIGCODEC_CLK>; + clock-names = "mclk"; +}; + +&smd_rpm_regulators { + vdd_l1_l2_l3-supply = <&pm8916_s3>; + vdd_l5-supply = <&pm8916_s3>; + vdd_l4_l5_l6-supply = <&pm8916_s4>; + vdd_l7-supply = <&pm8916_s4>; + + s1 { + regulator-min-microvolt = <375000>; + regulator-max-microvolt = <1562000>; + }; + + s3 { + regulator-min-microvolt = <375000>; + regulator-max-microvolt = <1562000>; + }; + + s4 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + + regulator-always-on; + regulator-boot-on; + }; + + l1 { + regulator-min-microvolt = <375000>; + regulator-max-microvolt = <1525000>; + }; + + l2 { + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <1200000>; + }; + + l3 { + regulator-min-microvolt = <375000>; + regulator-max-microvolt = <1525000>; + }; + + l4 { + regulator-min-microvolt = <1750000>; + regulator-max-microvolt = <3337000>; + }; + + l5 { + regulator-min-microvolt = <1750000>; + regulator-max-microvolt = <3337000>; + }; + + l6 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + }; + + l7 { + regulator-min-microvolt = <1750000>; + regulator-max-microvolt = <3337000>; + }; + + l8 { + regulator-min-microvolt = <1750000>; + regulator-max-microvolt = <3337000>; + }; + + l9 { + regulator-min-microvolt = <1750000>; + regulator-max-microvolt = <3337000>; + }; + + l10 { + regulator-min-microvolt = <1750000>; + regulator-max-microvolt = <3337000>; + }; + + l11 { + regulator-min-microvolt = <1750000>; + regulator-max-microvolt = <3337000>; + }; + + l12 { + regulator-min-microvolt = <1750000>; + regulator-max-microvolt = <3337000>; + }; + + l13 { + regulator-min-microvolt = <1750000>; + regulator-max-microvolt = <3337000>; + }; + + l14 { + regulator-min-microvolt = <1750000>; + regulator-max-microvolt = <3337000>; + }; + + /** + * 1.8v required on LS expansion + * for mezzanine boards + */ + l15 { + regulator-min-microvolt = <1750000>; + regulator-max-microvolt = <3337000>; + regulator-always-on; + }; + + l16 { + regulator-min-microvolt = <1750000>; + regulator-max-microvolt = <3337000>; + }; + + l17 { + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + }; + + l18 { + regulator-min-microvolt = <1750000>; + regulator-max-microvolt = <3337000>; + }; +};